Baxi Slim boilers have a wide range of models, boiler power from 15 to 62 kW. Smooth power control and built-in self-diagnosis system provide increased operating comfort and ease of maintenance. The modern design of the Baxi Slim boiler and its compact dimensions (only 35 cm wide) make it easy to place the boiler in any interior. You can choose a model with a built-in boiler or install a separate boiler with the same design next to the boiler (Baxi Slim UB).
Gas system of the BAXI Slim boiler
- Smooth regulation of boiler power in heating and hot water supply modes;
- Smooth electronic ignition;
- The boilers are fully adapted to Russian conditions. Operate stably when the inlet pressure of natural gas decreases to 5 mbar;
- It is possible to reconfigure the boiler for liquefied gas.
Hydraulic system of the BAXI Slim boiler
- The primary heat exchanger is made of cast iron;
- Built-in circulation pump (except IN models);
- Built-in storage boiler for preparing hot water (in double-circuit models) with its own pump;
- Heating circuit pressure gauge;
Temperature control of the BAXI Slim boiler
- Two temperature control ranges in the heating system: 30-85°C and 30-45°C (warm floors mode);
- Built-in weather-dependent automation (possibility of regulation using an outdoor temperature sensor);
- Regulation and automatic maintenance of the set temperature in heating and hot water supply circuits;
- Digital temperature display;
- Possibility of connecting a programmable timer.
Control and safety devices for the BAXI Slim boiler
- Digital self-diagnosis system;
- Ionization flame control;
- Pump blocking protection system (turns on automatically every 24 hours);
- Protective thermostat against water overheating in the primary heat exchanger;
- Draft sensor to control the safe removal of combustion products (pneumatic relay - for models with a closed combustion chamber, thermostat - for models with an open chamber);
- Pressure switch in the heating system - triggers when there is insufficient water pressure;
- Safety relief valve in the heating circuit (3 atm.) and in the hot water supply kennel (8 atm);
- Frost protection system for heating and hot water supply circuits.
Designations in the model name:
Fi- a boiler with a closed combustion chamber: combustion air can be taken from the “street”, the chimney is coaxial (pipe in pipe) or separate, the presence of draft in the chimney is not necessary.
i- a boiler with an open combustion chamber: combustion air is taken from the room where the boiler is installed, the chimney is traditional, providing natural draft.
N- models without a built-in pump, expansion tank, pressure gauge and safety valve.
Models BAXI Slim 2.300 And BAXI Slim 2.230 have a built-in boiler for preparing hot water.
The lineup Slim in boilers are produced by Baxi Corporation for heating various objects. This equipment is in greatest demand among owners of country houses and cottages. His price available to most buyers, boilers of this series They are characterized by a long service life, ease of installation and operation. They are accompanied by detailed instructions in Russian. However, we recommend that you contact our company’s specialists for installation and configuration of boiler equipment. This guarantees the safety and effectiveness of using the product in domestic and industrial environments.
Floor boiler Baxi Slim : basic information
These devices are highly efficient single-circuit floor-mounted boilers. They are equipped cast iron heat exchanger, electronic system ignition of the burner. There is automated flame control, which is carried out by ionization and by electronic control of gas fuel consumption. Other innovative technologies have also been developed that can reduce the risk of emergency situations to a minimum.
There are two types of boilers in the Slim model range. The first of them are supplied complete with hydraulics (there is a pump, expansion tank, pressure gauge). The power of these models ranges from 14.9 to 29.7 kW, the number of heat exchangers is from 3 to 5. The second type of boilers with a capacity from 22.1 to 62.2 kW are not equipped with hydraulic accessories. The power of the device is selected depending on the total size of the heated premises and the amount of heat loss.
Floor-standing gas boiler baxi slim – characteristics and advantages
The main dimensions and technical characteristics are as follows:
- Height – from 85 to 165 cm (depending on the model);
- Width – 35 cm;
- Depth – from 52 to 87.5 cm;
- The maximum permissible water pressure in the heating circuit is 3 atmospheres;
- The combustion chamber is open;
- Voltage in the electrical network – 230V;
- Power consumption – 15 kW;
- Energy efficiency class – A or A+
This equipment has high efficiency (over 90%), a stylish design traditional for Italian products, and compact dimensions. It is environmentally friendly, meets European energy efficiency standards, and has a simple and effectively understandable interface. There are options for additional connection of a water heater, timer, and outside temperature sensor. By resetting the burner you can use liquefied gas. This operation should only be carried out by certified employees of specialized companies.
Floor boiler models in
Due to its valuable performance properties, this convection boiler is one of the most popular in the model range. Its rated power is 29.7 kW, but thanks to the ability to regulate the gas supply, it can be reduced. This results in significant savings in fuel consumption.
Like other models, it has a nice design; the body is painted light gray. It can operate both on main gas (its consumption at maximum power is 3.5 m3 per hour) and on a propane-butane mixture (the same figure is 2.56 kg per hour). Capable of heating the coolant up to 85 degrees C.
The functions of power-on indication, automatic ignition, and flame level regulation are implemented.
The boiler is optimally suited for heating private houses with a total area of heated premises of 250-300 m2.
Floor boiler models in
This device has similar characteristics to the previous version, has the same design, but is capable of operating with a maximum output of 40 kW. Therefore we recommend buy to its owners of houses with a total area of heated premises up to 400-430 m2.
The boiler has a sophisticated electronic control system. Just like Slim 1300 in can run on natural and liquefied gas. The maximum fuel consumption, respectively, is 4.69 m3 and 3.45 kg per hour.
The manufacturer has thought through an effectively working security system. There is a constantly functioning auto-diagnosis, a gas control system, protection against overheating, freezing from pump blocking are implemented. Built-in safety valve.
If you decide to purchase one of the Baxi Slim in boilers, we recommend contacting our company. The main advantages of cooperation with us are as follows:
- Low prices for equipment due to direct contacts with manufacturers and distributors;
- Supplies only original products, no counterfeits;
- Individual approach to every customer;
- Strict fulfillment of contractual terms, including those related to deadlines;
- Our specialists are highly qualified, many of whom studied at authorized training centers of the Baxi Corporation and have the appropriate diplomas and certificates;
- Deliveries by personal vehicles and by transport and logistics companies cooperating with us in a short time.
In addition, thanks to constant contacts with Baxi, we can organize bonuses, additional discounts for regular and wholesale customers, and encourage them through various promotions. If you still have additional questions about the capabilities and nuances of using this equipment, contact our consultants. They will provide comprehensive information on Baxi domestic boilers, taking into account their use at home.
All products we supply are certified by Rostest.
Italian models of heating equipment are popular due to their reliability, a large number of built-in functions, as well as a good price-quality ratio. Atmospheric floor-standing gas boilers Baxi (Baksi), equipped with a cast-iron heat exchanger, operate in energy-independent mode and are presented in three basic modifications.
Types of floor-standing atmospheric boilers Baxi
Three basic modifications of Baksi boilers, manufactured by the Italian company of the same name, are distinguished by good thermal characteristics. When choosing a boiler, you should pay attention to several features:- Number of heat exchangers- Baksi 2-circuit floor-standing gas heating boilers with a built-in boiler are popular. The advantage of dual-circuit equipment is the ability to operate in flow-through mode for heating hot water, as well as accumulating hot water in a buffer tank.
Italian floor heating single-circuit gas boilers Baxi are designed for heating residential premises. If necessary, it is possible to re-equip the station and connect an indirect heating boiler with a capacity of up to 2500 liters. - Performance- maximum power of floor-standing boilers of the Baxi SLIM series is 110 kW. At the same time, the dimensions of the floor-standing boiler do not exceed 1200 mm in the HPS series.
- Electricity dependence- all equipment can operate in a completely non-volatile mode. Boilers with built-in circulation pumps require electricity to operate.
Thermal power (kW) | |||||||||
Gas consumption (m³/h) | |||||||||
Volume of water in the boiler (l) | |||||||||
Sections in the heat exchanger | |||||||||
Overall height (cm) | |||||||||
Overall width (cm) | |||||||||
Overall depth (cm) | |||||||||
All offered heating equipment has the following general thermal characteristics:
- Open combustion chamber- floor-standing versions have an atmospheric or convection combustion chamber. During operation, oxygen from the room is burned. Connection to a classic vertical chimney is provided.
- Stainless steel burner- the burner device is made of AISI 316 steel. The material is resistant to high temperatures, condensate, and has a long service life.
- Heat exchanger material- the boilers are equipped with a cast iron primary heat exchanger, as well as a secondary circuit made of copper.
Other characteristics depend on the selected model.
Boilers Baxi SLIM
The Baxi SLIM atmospheric floor-standing gas boiler has a large selection of power sizes, from 15 to 62 kW. As an additional option, an energy-dependent modulating burner is offered, which automatically adapts the operation to the actual heat needs of the room, as well as draft parameters and other operating characteristics. In addition, the SLIM series has the following features:
In the SLIM series, boilers with one and two heat exchangers are offered. In the basic configuration, the Baxi floor-standing gas double-circuit boiler has a built-in boiler. Single-circuit models can be optionally equipped with a storage capacity from 100 to 2500 liters.
Boilers Baxi SLIM HPS
The Baxi household gas floor-standing boiler with an atmospheric burner, SLIM HPS series, is characterized by high thermal efficiency. The device uses a special heat exchanger design made of highly ductile cast iron. To increase the heat transfer surface, special profile fins are used. This design feature has a positive effect on the reliability and quality of operation of the Baxi floor-standing boiler.The series has several distinctive features: 
The SLIM HPS series is designed for economical heating of large areas. The maximum boiler productivity is 108 kW.
Boilers Baxi SLIM EF
The Baksi floor-standing double-circuit gas boiler, produced in the SLIM EF series, is completely energy independent. The device contains an atmospheric burner. The design deserves special mention. The series is available in a gray case with a black control panel. The device of the SLIM EF floor-standing boiler includes a switch that turns off the gas pressure immediately after the flame goes out. The boilers are designed for connection to coolant systems. Maximum performance - 61 kW.
Rules for installation and operation of the Baxi floor-standing boiler
The technical characteristics of Baksi boilers determine the features of installation and operation. The manufacturer recommends following several recommendations:- The boiler's performance fully corresponds to that specified in the technical documentation. Productivity is calculated using the formula 1 kW = 10 m². To the result obtained, add a boiler power reserve of 15%. For double-circuit units, add another 15% for water heating.
- Equipment installation is carried out in accordance with existing SNiP and PPB. Before connecting a floor-standing boiler to the heating system, you must carefully study the operating instructions and find out whether the selected unit is suitable for the selected heating scheme.
- The technical requirements for installing Baksi floor-standing gas heating boilers are as follows: ceiling height of at least 2.2 m, total area of 8 m². The boiler room must have supply and exhaust ventilation.
Floor-standing gas boilers with cast iron heat exchanger. The range of Baxi Slim boilers is quite wide and will satisfy the desires of any consumer. For sale there are models for heating with an open and closed combustion chamber, models with a built-in boiler of 50 and 60 liters. Baxi Slim power range is from 15 to 62 kW. Electronic flame modulation and built-in self-diagnosis system provide increased ease of operation and maintenance. And the modern design and minimal overall dimensions (width only 35 cm) will allow you to easily place the boiler in any interior.
Brief description by model:
- Baxi Slim 2.300 Fi, 2.230 i, 2300 i are equipped with a built-in boiler;
- Models with the letter F in the series have a closed combustion chamber, i - an open type, IN - do not have a circulation pump;
- Baxi Slim 2300 Fi, 2230 i, 2300 i, 1230 Fi, 1300 Fi, 1150 i, 1230 i, 1300 i - equipped with a 10-liter expansion tank and a circulation pump.
Gas system Baxi Slim:
- Continuous electronic flame modulation, both in heating and DHW modes;
- Smooth electronic ignition;
- Stainless steel burner;
- The boilers are adapted to Russian conditions;
- Operate stably when the inlet pressure of natural gas decreases to 5 mbar;
- Can be reconfigured to run on liquefied gas.
Hydraulic system Baxi Slim:
- Cast iron primary heat exchanger;
- High-speed circulation pump with automatic air vent (except iN models);
- Separate pump for the boiler (in models with a built-in boiler);
- Pressure gauge (except iN models);
- Pump post-circulation;
- Possibility of connecting an external storage boiler for hot water.
Temperature control Baxi Slim:
- Two temperature control ranges in the heating system: 30–85°C and 30–45°C (warm floors mode);
- Remote control device with climate regulator (supplied separately);
- Built-in weather-dependent automation (possibility of connecting an outdoor temperature sensor);
- Regulation and automatic maintenance of the set temperature in the heating circuit;
- Regulation and automatic maintenance of the set temperature in the boiler (for models with a built-in or separate boiler);
- Possibility of connecting a programmable timer;
- Electronic temperature display.
Baxi Slim control and safety devices:
- Electronic self-diagnosis system;
- Ionization flame control;
- Protective thermostat against water overheating in the primary heat exchanger;
- Draft sensor to control the safe removal of combustion products (pneumatic relay - for models with a closed combustion chamber, thermostat - for models with an open chamber);
- Pump blocking protection system (turns on automatically every 24 hours);
- Safety valve in the heating circuit (3 atm.) (except for iN models);
- Safety valve in the DHW circuit at 8 atm. (models with built-in boiler);
- Frost protection system in the heating circuit and boiler;
Operating instructions and booklets Baxi Slim:
Floor-standing gas boilers BAXI with cast iron heat exchanger.
Boiler BAXI SLIM 62.2 kW without pump and expansion tank.
Wide range of models. Power range from 15 to 62 kW. Electronic flame modulation and built-in self-diagnosis system provide increased ease of operation and maintenance. And the modern design and minimal overall dimensions (width only 35 cm) will allow you to easily place the boiler in any interior.Gas system
Continuous electronic flame modulation, both in heating and DHW modes;
Smooth electronic ignition;
Stainless steel burner;
The boilers are adapted to Russian conditions. Operate stably when the inlet pressure of natural gas decreases to 5 mbar;
Can be reconfigured to run on liquefied gas.
Hydraulic system
Cast iron primary heat exchanger;
High-speed circulation pump with automatic air vent (except iN models);
Built-in boiler for hot water (in double-circuit models);
Separate pump for the boiler (in dual-circuit models);
Pressure gauge (except iN models);
Pump post-circulation;
Possibility of connecting an external storage boiler for hot water.
Temperature control
Two temperature control ranges in the heating system: 30-85°C and 30-45°C (warm floors mode);
Remote control device with climate regulator (supplied separately);
Built-in weather-dependent automation (possibility of connecting an outdoor temperature sensor);
Regulation and automatic maintenance of the set temperature in the heating circuit;
Regulation and automatic maintenance of the set temperature in the boiler (for models with a built-in or separate boiler);
Possibility of connecting a programmable timer;
Electronic temperature display.
Control and safety devices
Electronic self-diagnosis system;
Ionization flame control;
Protective thermostat against water overheating in the primary heat exchanger;
Draft sensor to control the safe removal of combustion products (pneumatic relay - for models with a closed combustion chamber, thermostat - for models with an open chamber);
Pump blocking protection system (turns on automatically every 24 hours);
Safety valve in the heating circuit (3 atm.) (except for iN models);
Safety valve in the DHW circuit at 8 atm. (models with built-in boiler);
Frost protection system in the heating circuit and boiler;
Installation of boilers of modern designs, using various types of fuel, allows you to ensure an optimal level of comfort in residential or industrial premises. There are many modifications of such equipment, taking this into account, before you buy this or that device, you should study the market. Modern single-circuit floor-standing gas boilers with a cast-iron heat exchanger use the most common and cheapest type of fuel - gas.
Such equipment can be installed not only in residential buildings, but also in any other buildings where constant autonomous heating is required, the only condition being a natural gas supply. Modern production offers a choice of single-circuit and double-circuit devices, so some gas boilers have very simple heating and water distribution schemes.
Many stores are engaged in activities such as selling gas boilers; as a rule, they have a wide range of different models, differing in many respects, including the installation method.
Both Russian and foreign gas boilers are sold; their prices are much higher than ours. When installing water heating devices on gas, you need to think about the chimney, and when making a choice between wall-mounted and stationary devices, you should know that for wall-mounted and floor-mounted boilers, project preparation is required and permission from government authorities is required. Prices for gas boilers are set depending on the use, power and area of the heated object.
Next model.
Loading...
